Chia Ming Machinery Co., Ltd.

Fully Electricity Automatic PET Stretch Blow Molding Machine

Home > Products > PET Series > Fully Electricity Automatic PET Stretch Blow Molding Machine

Model: CMS-W2 / W4 / M2 / M4

CMA-2000CD-E:

/ CMA-4000S:

/ CMA:

Features:

Fast setting position, low noise, clean and save power, no pollution.

Operation:

Servo motor controls open-closed mold, stretch and blow, chain movement.
Fast setting position: adjustable speed at any time.
Precision: under servo motor control, the precision will be controlled 0.001 m/m.
Low noise: the machine in running condition can be adjusted from high speed to slow speed, and it will not make loud noise.
Clean is the most special feature of servo motor which does not need any air or hydraulic lubricant. This machine save power consumption.

Fully Electricity PET Stretch Blow Molding Machine
Operation of Fully Electricity Automatic PET Stretch Blow Molding Machine

Semi-Electricity PET Stretch Blow Moulding Machine
Operation of Fully Electricity Automatic PET Stretch Blow Molding Machine

	Open-close Mold System Servo motor control makes speed-up, positions accurately, stabilizes, and increases efficiency, low noise, without pollution.
	Crankshaft System Drive screw adopts high hardness chrome-nickel steel (SCM450), quiet and stable. Drive board supported by 4 bearing steel makes proceeding smoothly.
	Stretch Blow System Servo motor drive enables accurate position. Control & adjust position easily through touch screen.
	Touch Screen Control System Combine all actions & heating system on the same panel board. Computer touch screen communicates with the PLC. All actions of the machine can be seen on the screen. The system diagnoses and displays the problems on the screen to make troubleshooting easter.
	Open-close Mold System (Economic Type) Curved arm adopts unilateral action, and the other side uses joint gear drive. Features of this design: few troubles, high speed, to close both mold plates at same speed, without closed mold line.

Specifications :

Model		CMSW2	CMSW4	CMSM2	CMSM4
Container	Max. neck diameter	Ø70mm~ Ø120mm	Ø70mm~ Ø120mm	Ø50mm~ Ø90mm	Ø28mm~ Ø50mm
	Max. production capacity	1100pcs/hr	2200pcs/hr	1200pcs/hr	2500pcs/hr
	Max. body diameter	Ø180mm	Ø180mm	Ø90mm	Ø90mm
	Max. container height	300mm	300mm	300mm	300mm
	Max. bottle capacity	6	6	1.5	1.5
	No. of cavities	2	4	2	4
Mould	Motor horse power of clamp cylinder	30kg/cm²	30kg/cm²	30kg/cm²	30kg/cm²
	Clamping stroke	260mm	260mm	190mm	190mm
	Carry pitch	228.6mm	228.6mm	114.3mm	114.3mm
	Mold center distance	228.6mm	228.6mm	114.3mm	114.3mm
	No. of preform mandrels	38	76	40	76
Heating oven	No. of ovens	8	8	4	8
	No. of infrared heaters in each oven	10	10	8	8
	Max. heating load	72kw	144kw	32kw	64kw
Air pressure	Low pressure	6kg/cm²	6kg/cm²	6kg/cm²	6kg/cm²
Air pressure	High pressure	UP to 35 kg/cm²	UP to 35 kg/cm²	UP to 35 kg/cm²	UP to 35 kg/cm²
Cooling water	Cooling capacity	4500kcal	4500kcal	4500kcal	4500kcal
	Water consumption	3m³/H	3m³/H	3m³/H	3m³/H
	Water temperature	8~12XC	8~12XC	8~12XC	8~12XC
	Pressure	5 kg/cm²	5 kg/cm²	5 kg/cm²	5 kg/cm²
Installation power		77kw	150kw	37kw	70kw
Total consumption power		<77kw	<150kw	<37kw	<70kw
Machine dimension		4500x2250 x2200mm	4500x2250 x2200mm	2500x1900 x2200mm	4500x2250 x2200mm
Machine weight		7 ton	14 ton	4.5 ton	7 ton

All specifications and designs are subject to change without notice.